West System
803 Glue Brushes

Disposable Brushes with Metal Handle

These brushes are useful in a wide variety of small bonding and coating applications.

Sterling
Special Tack Rags & Wood Stir Sticks

Every Paint or Varnish Job Should Start with a Tack Cloth

For final dust removal just before topcoat application. Lightly wipe surface, do not scrub. Change rag surface constantly to keep clean. Do not use solvents with tack rags.

US Chemical & Plastics
12"x12" Mixing Board

This special non-stick, non-absorbent plastic surface is ideal for epoxies and polyester compounds. It is easy to clean by flexing.

Fibre Glass-Evercoat
Everfix Epoxy Sticks

Cures Underwater

Repair manifolds, outdrives, trimtabs, exhaust lines, fuel and water tanks and lines. Patch fish boxes, ice chests, battery cases and buckets. Seal leaks. Insulate electrical connections. Form gaskets.
• Sets in 30 minutes
• Can be sanded, painted, drilled, tapped and filed
• Will not shrink or pull away
• Resealable tube prevents dry-out after opening

Fibre Glass-Evercoat
Aluminox Epoxy Sticks

Permanently Repairs Holes, Gouges, Cuts, Rivet Leaks in Aluminum Boats and RV's

Seals leaks in fuel and water tanks and lines, pipe joints, drain, exhaust lines, manifolds and mufflers. Repairs cracks in outboard-I⁄O lower units and outdrives. Works equally well on other materials including fiberglass, wood, other metals and ceramics.
• Cuts through oxidation and anoxidation to enhance ability to adhere to old aluminum
• Mixes easily by hand, like modeling clay
• Sets in 30 minutes
• Can be sanded, painted, ...

West System
804 Mixing Sticks

Reusable

A practical mixing, application, filleting and cleaning tool. The squared beveled end reaches mixing pot corners for thorough mixing and blending in fillers in addition to cleaning up excess epoxy. Cured epoxy pops off easily, so they can be used many times.
• Use rounded end to shape 3/8" radius fillets
• 3/4" wide x 5-1/2" long

West System
Poly Mixing Pots

Reusable

Cured epoxy easily pops out of these strong, reusable plastic mixing pots.

Weld Mount
Adhesive Dispensing Gun

1:1 Adhesive Plunger

Designed specifically for use with Weld Mount adhesive cartridges, this hand operated gun provides precise mixing and dispensing of the adhesive. Mixing tips are disposable⁄single use, and are sold separately.
• Gun only, adhesive and tips are sold separately
• For the viscous AT-4020 adhesive, choose the wide tipped AT-450 mixing tip
• For the lower viscosity AT-2010 adhesive, choose the narrow tipped AT-400 mixing tip

West System
Small Batch Epoxy Scale

Provides Confidence That Your Batch Ratios Are Correct

A “must have” if you frequently work with project-sized glue batches. This scale is specially configured for measuring small amounts of epoxy. It allows the accurate dispensing of as little as a few drops to as much as 4 fluid ounces of epoxy when calculating additive percentages and can be used to check the accuracy of dispensing pumps. It offers four weighing modes: grams, ounces, troy ounce and pennyweight, grams being the most useful for measuring small ...

Weld Mount
AT-2010 Acrylic Adhesive

Ideal for Metals; Fast 6-Minute Cure Time

Weld Mount AT-2010 is a unique adhesive. It has a 4 minute working time and cures in 5 - 6 minutes. Working strength is achieved in 15 -20 minutes at 72°F. This makes AT-2010 the ideal adhesive for applications which require an immediate high strength bond. Viscosity is medium, similar to thick molasses, and the single use, narrow tipped AT-400 mixing tube is recommended. Bonds to virtually any surface, including glass and most plastics except Starboard, polypropylene, ...

Fiberglass Cloth & Tools
Impregnating Rollers for Open Mold Laminating

Aluminum Roller with Wood Handle

• One-piece design
• Designed to roll air out faster and easier

West System
808 Flexible Plastic Spreader

Yellow

Flexible, double-edged, reusable spreader for flow coating, fairing, filling and applying fabrics. 3-1/2" x 6"

West System
809 Notched Spreader

White

This 4" x 4" plastic spreader has 1/8", 3/16" and 1/4" notches on three sides for quickly applying modified epoxy at a constant rate. A useful tool when laminating large panels.

US Chemical & Plastics
Plastic Spreaders

Yellow

• Extra-flexible yellow spreaders
• Sharp, tapered edge
• Extra-sturdy
• Sold by the each

3M
Spreader

Dark Yellow

• Dynatron
• 3" x 5"

Fibre Glass-Evercoat
Spreader Kits

Red

Set of three flexible, long lasting plastic spreaders in 2-1/2", 4" and 5" for fast, smooth application of resins and body filler.

3M
3M™ Resin & Putty Spreaders

Yellow

Designed for spreading body and fiberglass fillers, finishing putties, and resins. These spreaders have sharp edges, are flexible, durable and easy to clean. Cured filler pops off easily.

3M
3M™ Wetordry™ Rubber Squeegee

Made of flexible rubber. Used for removing slush created when sanding, or for applying glazing putty and plastic filler.

West System
Composites Fabricating Cartridge System

Dual-Cartridge System

PRO-SET adhesives are pre-thickened, two-part epoxy adhesives formulated for secondary bonding of laminated composites as well as steel, aluminum, cast iron, concrete, stone and most wood species. PRO-SET adhesives will bond these materials, to themselves or to one another in any combination. This versatility fits the requirements of the marine and composites industries, as well as the architectural, transportation and civil engineering fields.
• Three curing ...

3M
3M™ Automix™ Fast Cure Epoxy Adhesive

Epoxy Syringe Set and Application Gun

Two-part, clear epoxy that delivers strong, durable bonds within minutes after application. Makes difficult repair jobs easy when used to join parts made of plastic, metal, glass, fiberglass, wood, etc.
• 3 to 5 minute working life
• Handling strength is reached in about 5 minutes, with full cure in one hour
• For use with the 3M Automix applicator gun (#08191)
• For automatic mixing as the adhesive is being dispensed, use the ...

Weld Mount
AT-4020 Acrylic Adhesive

Viscous - Ideal for Vertical and Overhead Applications

Weld Mount AT-4020 is a specially formulated acrylic adhesive with high viscosity for holding Weld Mount studs and stand-offs with little or no sagging in vertical or overhead applications. Usually, the mount can be applied without having to hold it in place while the adhesive sets, greatly speeding your work time. AT-4020 cures in 10 - 12 minutes, and has working strength within 30 minutes at 72°F. Viscosity is high, similar to peanut butter, and the single use, ...

Weld Mount
Adhesive Dispensing Gun

1:1 Adhesive Plunger

Designed specifically for use with Weld Mount adhesive cartridges, this hand operated gun provides precise mixing and dispensing of the adhesive. Mixing tips are disposable⁄single use, and are sold separately.
• Gun only, adhesive and tips are sold separately
• For the viscous AT-4020 adhesive, choose the wide tipped AT-450 mixing tip
• For the lower viscosity AT-2010 adhesive, choose the narrow tipped AT-400 mixing tip

3M
3M™ Scotch-Weld™ Duo-Pak Adhesives

2-Part Adhesives in Convenient Pre-Measured Cartridges

Designed for use with the 3M EPX™ Plus II Applicator. The applicator comes with 2 (2:1 & 1:1) re-useable plungers for the various Duo-Pak mixing ratios. Nozzles are disposable and are sold separately; 10:1 plunger is sold separately, see table.
• NS = non-sag
• DP-100 - general purpose, fast setting (3-5 min.) rigid epoxy
• DP-110 - general purpose, fast setting (9 min.) flexible epoxy
• DP-190 - general purpose, slow setting ...

3M
3M™ Automix™ EZ Sand Flexible Parts Repair

2-Part Automix Cartridge

A two-part epoxy which offers a 10 minute worktime and can be sanded with grade 180 abrasives after only 30 minutes to produce an excellent featheredge. The convenient cartridge offers automatic measuring of parts A and B, and the option to use a mixing nozzle for automatic mixing. Product consistency is like thick epoxy and it finishes with a finger or tool. Use thin build coats for vertical and overhead jobs.
• Excellent for creating coves and radii on surfaces ...

Weld Mount
AT-2010 Acrylic Adhesive

Ideal for Metals; Fast 6-Minute Cure Time

Weld Mount AT-2010 is a unique adhesive. It has a 4 minute working time and cures in 5 - 6 minutes. Working strength is achieved in 15 -20 minutes at 72°F. This makes AT-2010 the ideal adhesive for applications which require an immediate high strength bond. Viscosity is medium, similar to thick molasses, and the single use, narrow tipped AT-400 mixing tube is recommended. Bonds to virtually any surface, including glass and most plastics except Starboard, polypropylene, ...

West System
Mini Pump Sets

West and Pro-set System Pumps

For the accurate metering of all group sizes of West System and Pro-set resin and hardeners. The 300 Mini Pumps accurately deliver the proper 5:1 ratio of resin to hardener with one full stroke of resin for each one full stroke of hardener.
• West System Kit includes three pumps: one for 105 resin, one for 205⁄206 hardeners, and one for 207⁄209 hardeners
• Proset System Kit includes two pumps for size 0 and size 1 containers: one for 125 ...

West System
306 Model A Dispensing Pump

For large projects, a dispensing pump will soon pay for itself by reducing mixing time and waste.
• Choose the correct pump for the hardener you are using
• Reservoirs hold one gallon resin and one quart hardner
• Convenient carrying handle
• Dispenses approximately 0.5 oz of resin⁄hardener per pump stroke

West System
309 High-Capacity Gear Pump

West System

Designed and built by Gougeon Brothers, this gear pump will provide great effciency to the home builder and professional alike. The metered 5:1 ratio of resin⁄hardener mixture is delivered at 5 quarts per minute with continuous rotation of the crank, yet can dispense smaller quantities with partial crank rotation. Reservoirs hold two gallons of resin, one gallon of hardener.
• Dispenses mixture in a 5:1 ratio
• Positive shutoff prevents resin ...

West System
High-Capacity Gear Pump

PRO-SET Laminating System

This high-capacity gear pump is designed and built by Gougeon Brothers for larger laminating operations. It delivers an accurately metered 3:1 ratio of resin⁄hardener at the rate of up to 5 quarts per minute with continuous rotation of the crank, but can dispense smaller quantities with partial crank rotation. Reservoirs hold two gallons of resin and one gallon of hardener.
• Dispenses mixture in a 3:1 ratio
• Positive shutoff prevents resin and ...

MAS Epoxies
Resin & Hardener Pumps

MAS Epoxy Systems

For use with quart, half gallon, gallon, four gallon and five gallon size containers to deliver proper 2:1 ratio of MAS resin and hardener.
• Pumps are sold as a resin⁄hardener set, pre-calibrated for proper mix ratio
• Pump color coordinates with resin (blue) and hardener (red) caps to prevent mistakes when changing containers

System Three Resins
Plunger Pumps

These pumps fit directly into the gallon, quart and pint bottles. With minor modifications the pumps can be fitted into the 2.5 and 5 gallon containers as well. The pumps come with a restrictor for the hardener pump, which pumps only 50% per stroke for the proper two to one ratio.

West System
807 Syringes

Reusable

These syringes can be loaded with epoxy mixture for injecting into tight spots.
• Ideal for hardware bonding and plywood repairs
• Holds about 0.5 fl. oz.

MAS Epoxies
60cc Syringe

Use this syringe to fill larger voids and holes.

BoatLife
60cc Syringe

Use to fill larger voids and holes.

West System
885 Vacuum Bagging & Cup/Tubing Kits

A complete starter kit for room temperature repairs and small laminating projects up to 13 square feet. The Venturi generator develops over 20" of mercury of a 10 psi vacuum at 1 SCFM. It is designed to run off conventional shop air compressors delivering at least 60 psi at 2 SCFM.
Bagging Kit includes:
Venturi vacuum generator with bronze muffler, two vacuum cups, 10' of 1/4" ID vacuum tubing, vacuum gauge, two junction "T" barbs, 15 sq. ...