5 items are in this product group
Automatic and Non-Automatic Models
Heavy duty construction for both commercial and pleasure boat use. Known for trouble free operation and reliability. 1-1/2" discharge.• Traditional, non-automatic models are typically operated with a float switch to sense water and activate the pump (sold separately)• Automatic models do not require a float switch. Controlled by computerized operation, these pumps will turn on every 2.5 minutes for about 1 second to sense for water. If water is ...
3 items are in this product group
Internal Float Switch Models
These higher volume Rule-Mate Bilge Pumps feature a pump and a non-mercury float switch in a single, compact housing. As the water level rises, so does the float switch, activating the pump when the water level reaches about 2-1/2" in depth; the pump will remain activated until the water level drops to approximately 3/4" and the pump senses no load against the impeller. There is no on⁄off “test” cycling and therefore no power use until the pump comes ...
1 item is in this product group
Dealer Promo Kit
Purchasing this package will provide you with a basic selection of Johnson Cartridge Bilge Pumps, Switches and Spare Cartridge Motors for your store, at an attractive price.• Kit includes:• (2) 32503 - 500 GPH Cartridge Bilge Pump• (2) 32703 - 750 GPH Cartridge Bilge Pump• (1) 26014 - Automatic Switch• (1) 36303 - Ultima Switch• (1) 28552 - 500 Spare Motor Cartridge• (1) 28572 - 750 Spare Motor ...
6 items are in this product group
Solid-State Sensor Models - No Float Switch Required
Eco-friendly Rule Mate series of bilge pumps feature a solid-state water sensing technology that eliminates the need for a separate float switch. When water enters the bilge and reaches height of 2-3/4", a sensor turns the pump on. After the water is pumped out, another sensor shuts the pump off. The sensors will only recognize water. In the event of an onboard oil spill, straight motor oil that enters the bilge will not turn the pump on.• All-in-one pump ...
4 items are in this product group
Heavy Duty and Built to Last
SHURflo's 1500 and 2000 GPH nylon bilge pumps offer a unique motor cooling system to ensure efficient peformance and long life. Installatin is a snap with the patented swivel base and 6' tinned wire assembly.• Continuous duty• Submersible• 6' tinned wire assembly• Anti-air lock• Swivel baseplate• 7.2"L x 6"W• 1-1/8" outlet port• Igntion protected ISO 8849• ...
Quality Bilge Pumps you Can Trust
SHURflo bilge pumps are built for the harsh marine environment to withstand the toughest conditions. Standard with 3' tinned wire assembly for below waterline installations and water cooled motors for extended life.• Continuous duty• Submersible• 3' tinned wire assembly• Anti-airlock• Tough nylon housing• 12 VDC• 2-3/8" round footprint• 4.2"L x 3.75"W• ...
Compact and Powerful
• High performance• Simple installation, multiple wire locations• Meets ISO8849 marine standard• Low amp draw means long battery life• Easy maintenance, access to motor cartridge and filter area• Large filter base ensures maximum surface area exposed to bilge water• Robust ABS fuel-resistant housing
8 items are in this product group
Filters Bilge Water to Remove Oil Contaminants
The Liberty Bay Overboard Oil Protection System (OOPS) is a low-resistance, specially engineered filter designed to economically remove oil contamination from discharged bilge water. It is simple to install and use, and prevents environmental damage (and potential fines) by oil contaminated bilge water. The OOPS is installed between the bilge pump and the overboard thru-hull fitting, similar to installing a sea strainer. The filter elements absorb any hydrocarbons present, ...
Compact, low profile design. Four chamber diaphragm water system pump. Provides 3.8 GPM⁄14.4 LPM of smooth quiet flow for up to 4 outlets at an energy saving low amperage draw. Corrosion proof base and marine grade components make the PAR-MAX Series the choice of serious boaters.• 3.8 GPM open flow rate• Snap-in ports included with pump 1/2" hose barb and 1/2" threaded (QEST type)• Pressure - cut-in: 20 PSI, cut-out: ...
2 items are in this product group
Harsh Environment Water System Pump
A new deluxe version of the PAR-MAX 4. It has the same special waterproof coating on the motor, and protective rubber boot on the pressure switch, as the 30700-series Heavy Duty washdown⁄livewell pumps, to give maximum corrosion protection in a harsh marine environment. Provides 3.8 GPM of smooth quiet flow to up to 4 outlets. Snap-in ports included with pump: 1-1/2" hose barb, and 1/2" threaded.• 3.8 GPM• Volts: 12 VDC• Pressure ...
9 items are in this product group
Pressure-Controlled Pump
• 3.5 gpm (13.2 lpm) open flow output• Self-priming up to 10ft • Four piston diaphragm sealed for smooth and quiet operation• Thermal overload protection automatically stops motor should it overheat due to overload, with auto re-start feature• Diaphragm design allows extended dry running• Pressure switch cut-in 15 psi (1.0 bar), cut-out 25 psi (1.7 bar), low pressure, or cut-in 20 psi (1.4 ...
• Transfer pump for shower and gray water• Runs dry without damage to the pump• Manual on⁄off switch or automatic level control may be connected to pump (not included)• Includes plug in ports for easy installation: (2) 1/2" barb ports• Install with a Flojet 1700 Series strainer (not included)• 3/4" port fittings and strainer also available (not included)• ...
End Suction Centrifugal Pump
The Rule General Purpose Pump is designed for use as a washdown pump and⁄or to circulate water to your livewell tanks. Heavy duty construction for use on commercial or pleasure boats. 1-1/2" inlet and 1-1/2" discharge outlet. The General Purpose Pump must be mounted below the waterline. It does not deliver high pressure, nor is it self priming. It delivers lots of water, but at low pressure.
Unique Trouble-Free Magnetically Driven Impeller
The Bait Sentry series of livewell pumps are designed for easy installation and trouble-free operation. With a magnetic drive, the motor and impeller are not mechanically connected, so the pump can ingest large amounts of debris without damage to the motor. If the impeller becomes locked, the motor magnet breaks free and the motor continues to run at a very low amp draw. There are no seals to burn out and dry run conditions are not a problem. The Bait Sentry has a patented ...
12 items are in this product group
Long-Life Motors
Designed to supply the volume of water required to keep bait and catch alive and healthy, these pumps feature long life motors for outstanding reliability, performance and durability. They are silent running and vibrationless and are a must on any serious fisherman's boat. This innovative design includes many new features including a quick, "push button" motor cartridge removal system and rotatable base for positioning the discharge hose. Each pump has an integral ...
Jabsco diaphragm pumps provide dependable service and top performance. Self-priming so they can be remotely mounted in a high and dry location. • Unique run-dry diaphragm design• Belt drive and rubber mounting pads reduce noise and vibration• Long life permanently Iubricated ball bearings• Corrosive resistant base assembly• Inlet and outlet ports for 3/4" ID hose except 34600 which has 1" ports• NOTE: ...
A powerful and efficient, sealed, automatic bilge pump. 1100 GPH at open flow, 973 GPH at 3.3 ft. head, 750 GPH at 6.7 ft. head. 1-1/8" hose outlet. Permanent-magnet motor, stainless steel shaft, and steel-reinforced seal ensure powerful, durable performance. Exterior mounting feet allow easy installation with no disassembly required. This centrifugal pump features an internal impeller guard to prevent clogging by any debris that might make it past the strainer⁄base.
Rule's largest capacity submersible pump. Thoughtfully designed, it incorporates two 4000 GPH pumps which discharge through a common 3" outlet, since the two pumps function independently, if one fails, the other will continue to operate providing back-up pumping capability. Replacement motor modules available.
750 GPH, 12-Volt Pump
S750 is sized for larger recreational boats. Our most powerful 3/4" outlet automatic pump! 750 GPH at open flow, 625 GPH at 3.3' head. Sahara Bilge Pumps include 36" lengths of 16-gauge tinned copper wire. Wire is caulked to prevent water from wicking through insulation jacket. All materials and components are state-of-the-art. Permanent-magnet motor, stainless steel shaft, and steel-reinforced seal.• Backed by Attwood's 3-year warranty• ...
For 3/4" I.D. Hose
Sahara Bilge Pumps include 36" lengths of 16-gauge tinned copper wire. Wire is caulked to prevent water from wicking through insulation jacket. Permanent-magnet motor, stainless steel shaft, and steel-reinforced seal for durable performance. • Float switch engages pump motor at 2" water level• Pumps 500 GPH at open flow, 350 GPH at 3.3' head• Draws 1.5 amps at open flow• Pumps bilge level down to 1/2"• 42" ...
Electric Bilge Pumps
• Upgradeable 360 to 500 to 500 Auto• Removable strainer for easy cleaning• Low profile design for narrow bilges• Can be mounted on horizontal or vertical surface• Choice of flow rate 25 or 35 liters (6-1/2" or 9-1/2 U.S. gallons) per minute• Hose connection 3/4"• Easy to clean with "twist lock" assembly⁄disassembly• Strainer designed to leave minimum water level ...
23 items are in this product group
34600 Series
Diaphragm pumps are self-priming so that they can be mounted above and outside of harsh bilge environments. Because they are mounted remotely, the intake hose can be routed to the lowest point of the bilge regardless of space limitations.• Self-priming• Quiet operation• Diaphragm allows dry running• Permanently lubricated ball bearings• Corrosion resistant materials throughout• 10.8 GPM• Dimensions: ...
Offers big 4.3 GPM flow, run-dry ability in a compact, low profile design. Heavy duty motor has a special waterproof coating for harsh environment applications. Same high performance when used as an intermittent duty bilge pump or as a continuous duty livewell pump. Motors are thermal overload protected and meet USCG requirements including ignition protection.• Includes 36200-0000 Pumpgard strainer• Dimensions - Height 4-1/16" (103mm), Width ...
PAR Light Duty pumps are inexpensive yet have performance and features of higher priced pumps. Self-priming allows pump be mounted above bilge and sump areas with only the intake hose in the bilge. Run-dry design. Tough plastic body has ports for 3/4" ID hose.
• Self-primes up to 10 feet above the bilge• Runs dry without damage to the pump• Manual on⁄off switch or automatic level control may be connected to pump (not included)• Includes plug-in ports for easy installation: (2) 3/4" hose barb ports and (2) garden hose ports• Also includes 3/4" hose barb inlet strainer• Dimensions: 3.75"H x 6.3"W x 9.9"L
12 Volt Flexible Impeller Pumps
Through the years, the Jabsco "Water Puppy" series has established a standard of excellence for low voltage DC, self-priming, motor driven pumps. Ideal for bilge and sump, livewell and washdown applications. Permanent magnet motors.• Self-priming to 4 ft. (Commercial Series is 6 ft.)• Output flows in Table are at 10 ft. of head• Bronze pump heads give good serviceability; flexible impellers pass small bilge debris with no problems
16 items are in this product group
AC Motor - 115V
6050 Series pumps have a totally enclosed fan cooled motor (non-CE)
115 VAC Motors
The 12210 series are the most compact of the AC motor pump units. The motor has replaceable brushes. They are not rated for continuous duty.
Jabsco mounting collars are available for versatile intake and outlet fitup. Outlet collar, Model 34856-0000, is used to adapt flange outlet to tubing connection for 3" (76mm) size blowers; Models 34744-Series, 35515-Series and 34739-Series. Weight 5 lb. (0.2 kg).
• 1" discharge diameter• Max. head 16'• Max. Solid Handling 1/6"• 1 year warranty
7 items are in this product group
General Purpose Pump
Can be used in many industries: Marine, farming, plumbing, contracting and more. In the marine industry use this pump for bait tank circulation, transfer oil, wash down, and utility dock pumps.• Easy to service and maintain• Will tolerate abrasive wear (this may affect performance - seek advice from your distributer)• Handles hard and soft solids without clogging• Non pulsating flow• Flow rate: up to 9.6 USgpm, maximum ...
18 items are in this product group
Replacement Parts Sold as Single Pieces Unless Otherwise Noted
The Choice of Motor Boat Builders for Ski and Wakeboard Ballast Systems
Wakeboarders will be pleased to learn that Jabsco now offer a water Ballasting Pump that can quickly add up to 30 kgs (66 lbs) of water per minute to ballast tank systems. The pump is reversible to both fill and empty ballast tanks and is self-priming and therefore will not air-lock.• Unique impeller compound - Yellow• Handles debris• Reversible• 8 gpm (32 lpm) flow• Easy service
20 items are in this product group
21 items are in this product group
Single Outlet, Thru-Hull Aerator
Three high-efficiency, high power centrifugal aerator pumps that move water at output capacities of 500 gph, 800 gph and 1200 gph. With their innovative engineering and compact design, Tsunami pumps deliver high output from a small package. The high output T-1200 is ideal for filling trim tanks on ski and wakeboard boats.• Move more water and oxygen into livewell tanks to keep fish active• Cooler-running motors, premium materials, watertight seals ...
Handy-Mate® 16PC
• Length: 16" (40.6cm) • Diameter: 1-1/2" (38mm) • Pumps: 10 oz. per stroke • 36" long 1/2" semi rigid intake tubing• 36" long 1/4" semi rigid intake tubing with adapter• Two 1-1/4" hoses: red for oil and flexible for water
