QT KIT JET BLK PERFECTION
Perfection®  2-Part Polyurethane Kits
Share THIS PAGE:

Perfection 2-Part Polyurethane - Grays & Blacks

Long Lasting, Ultra High Gloss, Superb Color Retention, Highest Abrasion Resistance

Availability: Make a selection

Sku# Make a selection
Item ID Make a selection
Mfg# Make a selection
loading image
Checking Your Price
Overview
Perfection® is the ultimate performing, 2-part polyurethane finish — providing an extremely durable, ultra high-gloss finish, with superb color retention.
Perfection has excellent chemical, impact & abrasion resistance, as well as superior UV protection.

• Use on topsides, superstructures, decks, etc.
• Professional-quality results made easy
• Unique package of HALS/UV™ absorbers together with the chemical cure of the polyurethane resin system provides the longest life possible, and protects against premature aging
• Resistant to a wide range of chemicals including fuels, mild acids & detergents
• NOTE - surface preparation requires primers, etc. - See below
• For application by brush, roller and brush, or conventional spray
• Thinner: Brushing - 2333N (10% max.); Spraying - 2316N (15% max.)
• Theoretical coverage is 540 ft³/gallon, practical coverage is 480 ft³/gallon; at least 2 coats recommended; 49% solids (vol.)

Surface Preparation —

BARE FIBERGLASS - Clean with Fiberglass Surface Prep YMA601. Flush with fresh water. To determine if surface is clean, run fresh water over the surface - if the water beads up or separates it is an indication of contamination on the surface. Wipe with Fiberglass Solvent Wash 202. Repair any defects with Interfill 830/833 Fairing Compound or Watertite, then sand with 120-220 grade (grit) paper and remove residue. Apply 1 coat of Interprotect 2000E (as required). Follow with 2 coats of Interprime 880 or Epoxy Primekote 404. Abrade with 120-220 grade (grit) paper. Remove sanding residue with 2316N or 2333N.

CLEAR EPOXY - Clean with Fiberglass Surface Prep YMA601. Flush with fresh water. Sand with 80 grade (grit) paper. Remove sanding residue with Fiberglass Solvent Wash 202. Repair any defects with Interfill 830/833 Fairing Compound or Watertite, then sand with 120-220 grade (grit) paper and remove residue. Follow with 2 coats of Interprime 880 or Epoxy Primekote 404. Sand with 220-320 grade (grit) paper. Remove sanding residue.

BARE WOOD - Sand with 80 grade (grit) paper. Remove sanding residue by wiping with Special Thinner 216, 2316N or 2333N. Apply 1-2 coats of Interprotect 2000E followed by 2 coats of Interprime 880 Finish Primer or Epoxy Primekote 404. Alternatively, apply 2 coats of Epoxy Primekote Y404 (thinning the first coat 25% with 2333N or 2316N).

BARE METAL - Sandblast or grind the surface of the metal to Sa 2½ / SSPC-SP5-85 - near white metal surface. Remove sanding residue. Immediately apply Viny-Lux Primewash 353/354 thinned 25% with Viny-Lux Solvent 355 followed by 1 coat of Interprotect 2000E. Alternatively, apply 1 coat only of Interprotect 2000E only (thinned). Fill and fair with Interfill 830/833. Seal with 1-2 coats of Interprotect 2000E. Follow the overcoating times on the relevant primer datasheet. Apply 1-2 coats of Interprime 880 or Epoxy Primekote 404.

PREVIOUSLY PAINTED SURFACES - Can be applied directly over two-part catalyzed coatings, that are in good condition, by cleaning with Fiberglass Surface Prep YMA601. Sand with 220 grade (grit) paper. Remove sanding residue with Brushing Reducer 2333N, Special Thinner 2316N, or YTA920. Abrade with 120-220 grade (grit) paper.
 
 
 
 
 
 
 

© Copyright Fisheries Supply Company 2013. All rights reserved.
Host-Name:410506-FISHERIE